To the knowledge base

Cannot access the internet via the FRITZ!Box

You don't have internet, although internet access is set up in the FRITZ!Box? ✔ Here's what to do.

Although the FRITZ!Box is connected to a fiber optic connection (Fiber to the Home, FTTH) and configured to access the internet over fiber optics, some or all of the computers, smartphones, or other devices connected to the FRITZ!Box cannot access the internet. One of the following messages may be displayed on the devices:

  • "No Internet, secured"
  • "No Internet access"
  • "No internet connection"
  • "Connected to device. Can't provide internet"

Simply proceed as described below. After each measure, check whether the problem is solved.

Note:All instructions on configuration and settings given in this guide refer to the latest FRITZ!OS for the FRITZ!Box.

1 Unlocking your FRITZ!Box

If you purchased your FRITZ!Box from a retailer, your internet service provider may have to unlock it first:

  1. Contact the customer service of your internet service provider and have them unlock the FRITZ!Box for your fiber optic connection, if necessary. Depending on the provider, you can either call their customer service or use an activation portal to activate it.
    • With some providers, the FRITZ!Box's "GPON Serial" on the bottom of the device is required to unlock it.

2 Checking the connection to the FRITZ!Box

For the device to access the internet via the FRITZ!Box, it must be connected to the FRITZ!Box and able to access it:

Deactivating the mobile network connection in Android

Normally Android smartphones or tablets can only be used to open the user interface of the FRITZ!Box with an interrupted internet connection if the mobile network connection is cleared:

  1. Enable airplane mode on the Android device to clear all connections.
  2. Only enable Wi-Fi on the Android device to establish the connection to the FRITZ!Box.

Opening the FRITZ!Box user interface

  1. Open the FRITZ!Box user interface with the device that cannot access the internet.
  2. If the device can access the user interface, continue with the next section. If you used an Android device to access the user interface, you can now deactivate airplane mode on it again.

3 Checking the fiber optic connection

  1. Open the FRITZ!Box user interface.
  2. Check whether "Fiber" is displayed as connected in the section "Interfaces" on the "Overview" page.
  3. If "Fiber" is displayed as "interrupted", follow the steps in our guide FRITZ!Box does not establish a fiber optic connection.

4 Enabling the FRITZ!Box's DHCP server

In the factory settings, the FRITZ!Box automatically assigns the correct IP settings to all devices via DHCP. If you disabled the FRITZ!Box's DHCP server, re-enable it:

  1. Click "Home Network" in the FRITZ!Box user interface.
  2. Click "Network" in the "Home Network" menu.
  3. Click on the "Network Settings" tab.
  4. Click "Additional Settings" in the section "LAN Settings" to display all of the settings.
  5. Click the "IPv4 Settings" button.
  6. Enable the DHCP server and define the range from which the FRITZ!Box assigns IP addresses.

    Note:The FRITZ!Box has the IP address 192.168.178.1 (subnet mask 255.255.255.0) and assigns IP addresses from xxx.20 to xxx.200 in the factory settings.

  7. Click "OK" to save the settings.

5 Configuring the device to automatically obtain IP settings

To ensure that the device always uses the correct IP settings, make sure that it automatically obtains its IP settings from the FRITZ!Box (this is the default setting for most devices):

6 Configuring a DNS server in the FRITZ!Box

In the factory settings, the FRITZ!Box uses the DNS server of the internet service provider for the name resolution of web addresses. If you set up other DNS servers in the FRITZ!Box, re-enable the DNS server of the internet service provider:

  1. Click "Internet" in the FRITZ!Box user interface.
  2. Click "Account Information" in the "Internet" menu.
  3. Click on the "DNS Server" tab.
  4. Enable the option "Use DNSv4 servers assigned by the internet service provider (recommended)".
  5. If the section "DNSv6 Servers" is displayed, enable the option "Use DNSv6 servers assigned by the internet service provider (recommended)".
  6. If the option "Encrypted name resolution in the internet (DNS over TLS)" is enabled, enable the option "Allow fallback to non-encrypted name resolution in the internet".
  7. Click "Apply" to save the settings and on the FRITZ!Box, confirm that the procedure may be executed, if you are asked to do so.

7 Installing the latest software for the device

  1. Install the latest software version for the device (for example Android, iOS) or the latest driver for the computer's network adapter.

    Note:
    Since Windows Update often does not offer the latest drivers, install the drivers from the manufacturer's website, for example from the Intel Download Center.

8 Configuring the device's firewall

The following step is only necessary if firewall software is installed on the device:

  1. Configure the firewall on the device to allow connections from the device to the FRITZ!Box. Refer to the manufacturer of the firewall for information on how to set it up, for example consult the manual.