Do bazy wiedzy
Dokument informacyjny #17

Caller ID is not shown for incoming calls

Caller ID is not shown on the display of your FRITZ!Fon when you receive a call:

  • The FRITZ!Fon does not show the caller ID.
  • The FRITZ!Fon does not show the number a caller has called.

1 Defining display names in the FRITZ!Box

The following step is only necessary if the telephone shows caller ID, but not the number that the caller called:

  1. Click "Telephony" in the FRITZ!Box user interface.
  2. Click "Telephone Numbers" in the "Telephony" menu.
  3. Click the (Edit) button for the respective telephone number.
  4. Enter a name of your choice in the "Display name" field.

    Example:
    You can enter "VOIP_12345", "provider_12345", "office", "private" or "12345" as the display name for the internet telephone number 12345.

  5. Click "Apply" to save the settings.

2 Checking the FRITZ!Box's call list

  1. Click "Telephony" in the FRITZ!Box user interface.
  2. Click "Calls" in the "Telephony" menu.
  3. Check which incoming calls (blue or red handset) caller ID is not shown for.
  4. If caller ID is not shown for calls to an ISDN or internet number, either your telephony provider did not enable CLIP for your line, or the callers do not transmit their caller ID.
    • If caller ID is not shown for calls to an analog landline number, continue with the next section.

3 Checking the analog telephone line and devices

The following step is only necessary if the caller ID is not shown when your analog landline number is called:

Checking CLIP support

  1. Disconnect the FRITZ!Box from the DSL splitter's telephone socket.
  2. Connect an analog telephone to the DSL splitter's telephone socket.
  3. If the telephone does not show caller ID now, either your telephony provider did not enable CLIP for your line yet, your telephone does not support CLIP, or the caller did not transmit his caller ID.

Connecting all telephones and telephony devices to the FRITZ!Box

  1. Connect all telephony devices (for example telephones, faxes) to the FRITZ!Box.

    Important:Connecting additional telephony devices or sockets to the telephone jack can cause errors.

Excluding another device as source of interference

Either a device connected to the FRITZ!Box or the power mains may be transmitting interference to the FRITZ!Box. Perform the following test to see if this is the case:

  1. Remove all devices and cables from the LAN ports and the USB port on the FRITZ!Box. If no devices were connected, connect a computer to a LAN port on the FRITZ!Box.
  2. If the error no longer occurs, a device connected to the FRITZ!Box was transmitting interference to the FRITZ!Box or the computer now channels it off. Normally, one of the following measures eliminates the cause of the interference:
    1. Use a power strip to connect the FRITZ!Box and all of the connected devices to the same electric outlet.
    2. Test different electric outlets and power strips.
    3. Use UTP network cables to connect devices to the LAN ports on the FRITZ!Box. UTP network cables do not have a ground wire and do not transmit interference to the FRITZ!Box, unlike STP network cables such as the one included with delivery.

      Important:If the problem occurs with a FRITZ!Powerline device, use the UTP network cable included with the FRITZ!Powerline device.

    4. If a device connected to the USB port is transmitting interference to the FRITZ!Box, connect the device to a USB port on your computer instead of to the FRITZ!Box.

Signal quality is too low

If your FRITZ!Box still does not show caller ID for incoming calls, the signal quality of your analog landline is too low.

Compared to simple telephones, PBXs always place higher demands on the signal quality of analog telephone lines. The FRITZ!Box is capable of recognizing and processing all incoming signals correctly well beyond the specification limits. However, when used on lines subject to much interference, the FRITZ!Box's tolerance to errors is slightly lower than that of an analog telephone connected directly to your line. Therefore, under some circumstances, a telephone that is connected directly to your line can evaluate the CLIP information even though the FRITZ!Box cannot. This is not due to an error with the FRITZ!Box; instead, it is because the signal quality of the analog landline is too low.

Wybór języka